New Seal Kit Fits For Cat Pump Model 30 31 34 35 310 340 350 310B 310S 30623
Product Features: 【Perfect Fit】 Seal Kit for Cat Pump is compatible with Cat Pump 30, 31, 34, 35, 310, 310S, 310B, 310W, 340, 340S, 340W, 350, 350S, 350B, 350W models. Seals are recommended to be changed every 1500 running hours. 【Solve Water Leakage Issues】 The seals may need to be changed if your Cat Pump high-pressure cleaning pump pressure is low, water leak below the head or the pump is running rough. High quality replacement kit for your Cat Pump seal set with affordable price. Save your charge and Keep your high-pressure cleaning pump at peak performance! 【Set of 3】 The seal kit (30623) comes with High-Pressure Seals with S Seal (43307) X3, Low-Pressure Seals with S-Spg Seal (43305) X3, Seal Case O-Rings (14200) X3, Plunger Retainer O-Rings(17399) X3, Long Tab Wicks (43302) X3. 【Built to Last】 Made of durable NBR (nitrite Buna-N) rubber and steel material. Withstand temperatures up to 160°F. Excellent corrosion and water resistance, anti-rust performance ensure long-lasting use protection for your Cat Pump. 【100% Satisfaction Guarantee】We strive to give our customers excellent service. All Sixcow products support 30-Day money-back guarantee, 12-Month warranty for quality-related issues. Simply return it for your warranty. Quick & Easy Installation STEP 01: Remove the maniford: Use a 8mm wrench to remove the 2 hex socket head screws. Seperate the maniford and crankcase: Use 2 flat tip screwdrivers to pry maniford away from the crankcase. Use a rubber hammer to completely remove maniford from crankcase place. STEP 02: Remove the low-pressure seals, seal case o-ring and high-pressure seals: Put the maniford on flat surface with low pressure seals facing up. Place a flat tip screwdriver under the low pressure seal and pry upward to remove. Be careful not scratch the inner diameter surface of the steel case where the low pressure seals are located. Inspect the inside of the low pressure seal for wear or damage. Using a half inch seam case tool or tee wrench remove the seal case. Inspect the seal case o-rings for cut nicks or damaged. Use a flat tip screwdriver under the high pressure seals and pry upward to remove. STEP 03: Install the low-pressure seals, seal case o-ring and high-pressure seals: Before installing , apply a liquid gasket to outside surface of the high pressure seals. With the flat side facing up, put the high pressure seals into place. Replace a new o-ring on the seal case, apply liquid gasket to the o-ring on the seal case. Install the seal case with the o-ring down into the mainford and thread into maniford. Using your seal case tool or tee wrench to tighten. With the spring side facing down, put the low pressure seals into place. STEP 04: Replace the wicks and small o-rings: Remove the nylon oil pan. Remove the two-piece seal retainer with wick. Put apart the retainer by hand, replace the wicks. Ensure the hole in the retainer is facing down when reinstalling. Use a 12 mm wrench lossen and remove the plunger retainer, replace the small o-ring on it. Apply thread sealant on the end of the plunger rod. Install plunger assembly and tighten using a 10 mm wrench torque to specification. With the hole and long tail of the wick facing down, install the plunger retainer. Put the oil pan back in place. STEP 05: Adjust to specification: Before reinstalling the maniford, rotate the crankshaft so that the outside two plungers are even up for this distance from the crankcase. Install the maniford by hand, ensure even alignment. Use a rubber hammer to ensure maniford is flush to crankcase surface. Reinstall the two hex socket head screws. Use a 8mm wrench to tighten and torque to specification. Payment ★. Buyers are welcome to use the following payment methods: payoneer, paypal, credit card, debit cardand many other mothods. Shipping ★. After your payment is completed, the item will be shipped from the US warehouse within 1-2 business days. ★. We only ship to confirmed ebay addresses. Your ebay address MUST MATCH your Shipping address Returns ★.We accept 60 days return guarantee for all Items. If you are unsatisfied with the item, you may send it back within 60 days of receipt, and then you will receive refund. ★.For returns caused by product quality issues, we will bear the cost of the return. For returns for other reasons, return costs may need to be borne by the buyer. ★.All returned products must be in their original condition and packaging. Unfortunately, if products have been assembled or modified, we cannot take them as returns. ★.It is important that we know when your return is expected. Please save your return tracking number or post receipt, and email it to us. We need this in case there are any issues during transit. ★.Refund will only be issued upon our receipt of the returned parcel. Please allow 2 working days for us to process with your return. Contact Us ★. We will reply your message within 24 hours Mon-Sat, and 48 hours on Sunday. Feedback ★.Welcome to leave your positive feedback, it will help other customers have a better shopping experience. ★.Please contact me before leaving neutral or negative feedback. Our customer service representative will do our best to solve the problem for you, thank you! All rights reserved.
ANP-92 ANP92 Metal Clutch Plate 5″ Center Hole fits Malish Brush
This metal clutch plate with a 5″ center hole is designed to fit the Malish Brush. It comes with a warranty of 1 year and is made in the United States. The clutch type of this plate is LM92 and it weighs 0.350 lbs. This product falls under the category of scrubber and buffer parts and accessories, which is a part of the larger category of floor and upholstery cleaning supplies. It is ideal for business and industrial cleaning and janitorial purposes. Machine Application: Generic Not sure will this part fit?Please contact us for compatibility. We can search quickly and confirm or find you the correct one! We usually respond to messages in 10-15 mins during working days Monday to Friday from 6AM to 3PM PST. SAME DAY SHIPPING (CUTOFF TIME 2PM PST / 5PM EST MON – FRI)30 DAY RETURNS (BRAND NEW CONDITION)1 YR WARRANTY RETURN POLICYOur goal is to make you 100% satisfied in all transactions and parts needs. If you are not satisfied with our product or you ordered an incorrect part, simply message us and we will issue RMA within 12-24 hours.Our returns are hassle-free and simple and we do not charge restocking fee.If we sent defective or incorrect part, we take care of return shipping and provide full refund.If you ordered incorrect part, then you pay return shipping and get full refund on product.You need correct replacement? Just let us know and ourparts specialist will help right away!Parts returned to us need to be uninstalled and in original box. Same day shipping and tracking available within 12 to 48 hours. We stock over 5 million material handling parts, just message us and we will get anything you need
Pulsar4hp 3/8″ Npt 10.5 Gpm 4500 PSI Trapped Pressure Unloader Valve
Feature: General Pump PULSAR4HP Unloader with 3/8″ NPT threads.For use with many pressure washers.Maximum Volume 10.5 GPM Rated Pressure 4050 PSI Maximum Pressure 4500 PSI Maximum Temperature 195° Note: The valve has been designed for continuous use at a water temperature of 140° F. It can operate for short periods at a maximum temperature of 195° F. NEW improved design! Reduced pressure loss Makes for easier gun operation Extremely reliable Easy maintenance Includes knob fitted with locknut for minimum working pressure adjustment Package Including： 1*General Water Pump Notes: .
10.5 GPM 4500 PSI General Pump PULSAR4KHP Trapped Pressure Unloader Valve US
Key Points: NEW improved design! Reduced pressure loss Makes for easier gun operation Extremely reliable Easy maintenance GPM up to 10.5 Key Features: General Pump PULSAR4HP Unloader valve with 3/8″ NPT threads. For use with many pressure washers. Note: The valve has been designed for continuous use at a water temperature of 140° F. It can operate for short periods at a maximum temperature of 195° F. Please check product compatibility carefully to ensure it is the product you need So as not to waste your time and energy on return Details: .
Trapped Pressure Unloader Valve For 4HP PULSAR4HP 3/8″ NPT 10.5 GPM 4500 PSI
Feature: General Pump PULSAR4HP Unloader with 3/8″ NPT threads.For use with many pressure washers.Maximum Volume 10.5 GPM Rated Pressure 4050 PSI Maximum Pressure 4500 PSI Maximum Temperature 195° Note: The valve has been designed for continuous use at a water temperature of 140° F. It can operate for short periods at a maximum temperature of 195° F. NEW improved design! Reduced pressure loss Makes for easier gun operation Extremely reliable Easy maintenance Includes knob fitted with locknut for minimum working pressure adjustment Package Including： 1*General Water Pump Notes: .
ALL-CARB 10.5 GPM 4500 PSI General Pump PULSAR4HP Pressure Unloader Valve
Caution: Minor differences in product design may result in different model numbers. Please check the picture carefully to see if it matches your product. If you are not sure if this model is right for you, please feel free to contact us. Suitable for: General Pump PULSAR4HP Unloader valve with 3/8″ NPT threads. For use with many pressure washers. Features: Maximum Volume: 10.5 GPM Maximum Pressure: 4500 PSI Rated Pressure: 4050 PSI Maximum Temperature: 195° Inlet: 3/8″ NPT-F Outlet: 3/8″ NPT-F Bypass: 3/8″ NPT-F .
Trapped Pressure Unloader Valve For 4HP PULSAR4HP 3/8″ NPT,10.5 GPM,4500 PSI
Key Features： General Pump PULSAR4HP Unloader with 3/8″ NPT threads.For use with many pressure washers.Maximum Volume 10.5 GPM Rated Pressure 4050 PSI Maximum Pressure 4500 PSI Maximum Temperature 195° Note: The valve has been designed for continuous use at a water temperature of 140° F. It can operate for short periods at a maximum temperature of 195° F. NEW improved design! Reduced pressure loss Makes for easier gun operation Extremely reliable Easy maintenance Includes knob fitted with locknut for minimum working pressure adjustment Package Content： 1*General Water Pump .
Maximum Volume General Pump 4500 PSI Trapped Pressure Unloader Valve 10.5 GPM
Product Description： Highest After-Sales Guarantee Low Cost,Highest Cost Performance Brand New & High Quality Durable And Easy To Install Specification： Maximum Volume 10.5 GPM Maximum Pressure 4500 PSI Rated Pressure 4050 PSI Maximum Temperature 195° Inlet 3/8″ NPT-F Outlet 3/8″ NPT-F Bypass 3/8″ NPT-F Note: The valve has been designed for continuous use at a water temperature of 140° F. It can operate for short periods at a maximum temperature of 195° F. General Pump PULSAR4HP Unloader valve with 3/8″ NPT threads. For use with many pressure washers. Package Including： .
4500 PSI 10.5 GPM General Pump PULSAR4KHP Trapped Pressure Unloader Valve
Specification: Maximum Volume 10.5 GPM Maximum Pressure 4500 PSI Rated Pressure 4050 PSI Maximum Temperature 195° Inlet 3/8″ NPT-F Outlet 3/8″ NPT-F Bypass 3/8″ NPT-F Description: General Pump PULSAR4HP Unloader valve with 3/8″ NPT threads. For use with many pressure washers. Note: The valve has been designed for continuous use at a water temperature of 140° F. It can operate for short periods at a maximum temperature of 195° F. Good quality, good operation. Please check pictures for more details. If you have any issues about the model, please contact with us! Feature: .
3/8″ Npt 10.5 Gpm 4500 PSI Pulsar4hp Trapped Pressure Unloader Valve
Feature: General Pump PULSAR4KHP Unloader with 3/8″ NPT threads.For use with many pressure washers.Maximum Volume 10.5 GPM Rated Pressure 4050 PSI Maximum Pressure 4500 PSI Maximum Temperature 195° Note: The valve has been designed for continuous use at a water temperature of 140° F. It can operate for short periods at a maximum temperature of 195° F. NEW improved design! Reduced pressure loss Makes for easier gun operation Extremely reliable Easy maintenance Includes knob fitted with locknut for minimum working pressure adjustment Package Including： 1*General Water Pump Notes: .